Fasade Traditional 1 18.5-in x 24.5-in Oil-Rubbed Bronze Backsplash Panels
$23.98
- Get the look of high-end designer backsplash panels without the designer cost
- No contractor required, DIY-friendly project can be completed in just a few hours
- The backsplash panels can be cut with a snip, scissors or utility knife for quick and easy installation
- Get the look of high-end designer backsplash panels without the designer cost
- No contractor required, DIY-friendly project can be completed in just a few hours
- The backsplash panels can be cut with a snip, scissors or utility knife for quick and easy installation
- Installs with 2-sided tape or polyurethane construction adhesive (not included)
- 18-In x 24-in backsplash panels are available in 13 styles and 18 finishes to provide over 200 combinations to meet homeowner needs
- Perfect for remodeling or new construction, panels are water- and corrosion-resistant for exceptional durability
- Panels are resistant to impacts and stains – simple to clean using warm water and soap with a soft cloth
- Matching inside corner-trim and edge J-trim pieces are available (not included)
- Backsplash panel will measure 18-in x 24-in once installed due to 1/2-in overlap for seamless application; refer to specs for actual measurements
| Weight | 0.88 kg |
|---|---|
| Dimensions | 19.0 × 25.0 × 0.2 cm |
| Brand | Fasade |
26 reviews for Fasade Traditional 1 18.5-in x 24.5-in Oil-Rubbed Bronze Backsplash Panels
Add a review
Related products
Backsplash Panels
Fasade Monaco 18.25-in x 24.25-in Gloss White Backsplash Panels
$69.89
$23.98
Backsplash Panels
Inoxia 31-in x 30-in Stainless Steel and Black Backsplash Panels
$179.00
Backsplash Panels
Fasade Quilted 18.25-in x 24.25-in Matte White Backsplash Panels
$69.89
Backsplash Panels
Fasade Ripple 18.25-in x 24.25-in Gloss White Backsplash Panels
$69.89
$96.83
Backsplash Panels
Fasade Lotus 18.25-in x 24.25-in Galvanized Steel Backsplash Panels
$104.89
Backsplash Panels
Fasade Traditional 1 18.25-in x 24.25-in Gloss White Backsplash Panels
$72.68
Anonymous –
Very affordable and quality products
Anonymous –
While on the pricy side, this material is heat resistant and fairly easy to work with and cut with utility scissors. The provided channeling for the top portion really allows some flexibility when cutting and does not require exact measurements as the channeling can be moved. One tip though…use extra extra two sided tape. At first I was using three strips the length of the material and in a couple days found the edges to be coming up. Another tip, place aluminum foil in the corners as this material was not really designed for corners nor is there channeling available for corners. That would be the one negative to this product.
nan –
It looks great. I bought this to replace the peel-and-stick sheets I had previously used as a backsplash, which kept peeling off at the edges. These panels are thin enough to cut and trim with a pair of shears, yet rigid enough to hold in place for trial fittings. The Liquid Nails construction adhesive stays pliable long enough to adjust placement then holds it tightly in place.
Anonymous –
looks good
Anonymous –
I absolutely love the finished look. It was so easy to cut and install ❤️
Anonymous –
I installed this product and love the way it turned out. My kitchen had unattractive back splash, but would have been too difficult and costly to have removed. I bought this tile and transformed my kitchen in 1 day! It is a bit expensive but still much cheaper than other alternatives. Only thing I would suggest is do not use the tape, buy an adhesive. I used the tape and within 2 months it started falling off. I re-applied with adhesive and it is just fine now. I would suggest this for anyone wanting a makeover, can be done in 1 or 2 days easily.
Anonymous –
This product is beautiful and very easy to cut to design it how you want
Anonymous –
I bought this product about 2 years ago to use over my stove as my backsplash area in the entire kitchen is just primed wall. I was worried about the durability of the product so I only did the small space between the range and the hood (where I figure it would take the most abuse from heat and splatter). It came out great in the small space we used it in and it needed 0 maintenance for the next 2 years. It was not until 2 months ago that my wife touched it and was amazed in finding out it wasn’t metal. She loved it so much I began this weekend pulling down the two pieces we put up previously and I am installing it on the entire kitchen. A few notes:
1. Contrary to a lot of the other reviews here I did use the tape on the section I did over the stove and it held great (with no support under it from a counter#. In fact it held so good It tore one of the old panels and pulled the primer off the wall when I removed them.
2. If you are using a repeating pattern like I did be extremely careful when laying out and cutting as not getting them lined up perfectly is very obvious. #Using a border will allow for about 3/16in of play#.
3. I cut mine with standard household scissors and it cut great #used a box cutter to get a cut started for the outlets#.
4. The panels are expensive and it cuts easily so always cut on the larger side and shave down where you need to. you can always cut more but you can’t add.
5. Use the borders, they add such a finished look to it and, as mentioned before, they help give you a little play to line it up perfect.
6. You cannot do a kitchen in two hours if you want it to look good. Give yourself time to do it right. I have about 30 Linear ft of backsplash I’m doing and given what I’ve done so far I estimate about 8-9 solid hours of work to get it right. This is considering I am quite an experienced DIYer. The picture I’ve attached is after about 2 hours and consists of 4 panels and 8ft #one I didn’t even have to cut) but it looks amazing and is more than worth the time.
My only issue is I’ve had to go to three different lowes in my area to get enough material. Everyone carries plenty of panels but not the borders. Considering a middle section that you are just doing the top and bottom border on needs about 4 pieces of border per tile, having 20 panels in stock and 8 borders makes for an interesting hunt and clearing of shelves at multiple locations.
Anonymous –
I was hesitant to use this product at first but I’m sure glad I did. I was afraid it would make my kitchen look dark and cheap but it did quite the opposite. Paired with the Matching Finish Outlet Covers, new black appliances and a black/tan mix counter top from gave my kitchen the WOW factor it was missing. Everyone that sees it comments on how much they love it. I only wish now that I had installed it myself instead of paying a professional. I found out after the fact that he had no prior experience with installing this product either. As I watched him install it, I realized how easy it was and felt that I would have done a better job myself (and saved myself a $200 labor charge). He quickly learned that it’s too easy to slip with a razor knife and is not the way to go. He ultimately used regular sissors to cut the panels and trim pieces, but I agree with other reviewers that using a tiny drill bit would make cutting out outlet and light switch openings much easier and a lot neater. He also left adhesive “fingerprints” here and there which I haven’t been able to remove. DO NOT use a magic eraser sponge on the trim pieces as it erases the finish right off. I found this out the hard way but was able to repair the spot with a piece of the Matching Finish Outlet Cover. This product is as easy to keep clean as ceramic tiles and I would highly recommend it.
Anonymous –
Durable and easy to install
Anonymous –
I had to buy nine panels. I first thought I would like the silver cross hair color, because I recently bought new stainless steel kitchen appliances. However, I bought all the colors had and then picked the Bronze to match the cabinet door/drawer pulls and exchanged the rest.
My kitchen required this backsplash go around a window, accommodate 7 outlets (one double) and turn a corner. If I had it to do over again, I would start at the corner. I used scissors for all cuts except outlets, but it is not easy to cut with either scissors or utility knife. I drew paper templates with very large graph paper before I cut any of the panels. I had to cut every piece for height because my formica countertops had a low backsplash built in. All but two panels had to have cutouts for outlets, and one piece for the window and outlets was nearly impossible. You can see it in the first image. I pieced it together out of scrap, then taped it together to cut out of a fresh panel.
I used the tape to attach , but it really needs another adhesive as well. Having so many outlets at least made if feel better secured to the wall. The outlet covers really finish it off well. Love the finished product.
Anonymous –
It’s and feels like the real thing.
Anonymous –
Just some advice for anyone wanting to undertake this project:
– Double sided tape is fine for areas not susceptible to moisture or constant heat (This eventually will dry out any tape adhesive and make it fail)
– Matching the pattern on the corners is a pain, but keep an open mind for workarounds that can look just as good.
– If you get the J-Trim, and corner pieces, you don’t necessarily need a perfect cut.
– Use a medium to heavy-duty pair of shears or snips, with all the ridges and dips in the pattern, scoring it with a box-cutter type blade can be a lesson in extreme frustration unless you are making a small cut out for an outlet or switch (MEASURE A LOT!), your blade can jump unless you add pressure before getting to an area, this can cause you to slip and cut yourself (didn’t happen to me, but I can see it happening).
– Don’t use more adhesive than recommended, and prep the area with a rough grit sandpaper for better adhesion, you don’t have to use power or a lot of pressure, just enough to burr the surface to allow the adhesive to grip, also, rubbing alcohol to clean the backs before applying adhesive and mounting.
– The stickers on the back state the overlap edges are 1/2″, it’s closer to 1/8″, this can be important.
– I’ll say it again…Corners are awful to get right, especially if you get to one and you are a couple inches to go, and your scrap pieces don’t match correctly, just hope it is in a blind area.
– If you have the option, use the brown colored adhesive, I used the standard Loctite type, some of the crud bled out after it settled, a plastic scraper, Goo-Gone, and/or alcohol pads will be your buddy.
– Understanding that theft is an issue, but almost every one of my panels had a not easily removed sticker with anti-theft devices under them, not a big noticeable deal, but if you’re as OCD as I am about making projects perfect, this could be a concern.
– If you have a short, Vietnam-era kitchen, you may have a lot of waste that you can’t use in another area.
– try not to overlap more than two panels, like I did in a 4×4 grid…I had to snip one of the panels underneath two others for it to sit flush.
– Getting frustrated is your worst enemy, leave it alone for the night and come back with a fresh head if you have a difficult kitchen like I do.
– The end result makes the wife happy, now I can get my lawn mower I want, and other toys.
I initially purchased 10 panels, completely winged the installation with nothing but the instructions on the sheet, a pair of medium duty shears, and some Loctite construction adhesive. I had to pull off the old backsplash from my 1968 house, which had a vinyl stick-on over old wood wall panelling, removing this came off like string cheese. After that, I was able to cut the backer I was using, which I treated with an anti-mold/water resistant solution, lightly sanding the wood once I mounted it on the walls. I found myself misjudging a lot of cuts because the product says 1/2″ overlap when it was closer to 1/8″, solving that issue early on, the pieces went up easily, a couple places had some air bubbles trapped in, but nothing that clever use of a couple 2×4 scraps and spreader clamps was not able to fix. My biggest challenge I found was the corners, after consulting with my better half, I decided I would get some cove moulding and paint to match, then glue/nail them in for a more uniformed look. I also learned that if you have to leave a specific area overnight due to frustration or other issues, always leave a 1/2″ area on the edge unglued as it will allow you to slide the next connecting panel underneath without having to chisel off dried adhesive. Starting the project with a relative plan was helpful, I found it easy to measure and write down the areas on the back panel, then measure again when I got to that spot.
But enough about all that, the plastic is durable, I dropped a couple, and while it did maybe ding a corner, it wasn’t so bad that it wasn’t easily covered up, or cleverly hidden. making the pattern match up on connecting panels was a breeze, with the exception of the corners of the room, notably when I got to them and had 2-4 inches left, too much for the corner and J-strips to hide. Thankfully, this plastic doesn’t retain adhesive accidently spilled on it, as long as you have a wet rag handy to fix your oopsies.
I found it to be a bit pricey for plastic, but let’s see how it holds up long term to determine if the value is there, considering wanted to charge me 800$ for a different style backsplash installation, not including removal of the old stuff and new paneling (that quote was around 1100$), I was able to sweat my way through installation for less than half what it would have cost to have a pro do it. My wife gleamed with joy when I revealed it to her after completion. Our old kitchen is starting to look new again, replacing countertops, installing a dishwasher (one didn’t come with the house), and a new faucet. Next in line is painting the solid oak cupboards, replacing the oven, and ripping off wall paper ceiling borders, then all new flooring. We have taken an old school kitchen, and not only made it ours, but we made it appealing when the day comes we are ready to sell it, but after the work I have personally put into it, I hope that day doesn’t come anytime soon.
My almost knows me by name, i’m sure they will see a lot more of me in the coming months.
Anonymous –
This is a beautiful/ E-Z way to cover tired old walls or create major aesthetic changes. Resolved several issues during the kitchen remodel and opening doors to an easy bathroom fix! The variety of colors, patterns, and size of repeat offer a lot of options for a number of applications. It goes up fast, looks good, seals easily so won’t rust, mold, or mildew.
Anonymous –
We studied hard and it was a tough decision to make. Tile, glass or plastic? In the end it came down to ease of installation, coloring, and price.
We bought numerous tile and several colors of the Plastic and had them sitting on the counter for a week or so. In the end we settled on the bronze plastic, largely because of the dramatic color and low price.
We have stainless appliances. The stove has a black glass top and the sink is black faux granite. The countertops are light and the cabinets are honey colored maple.
The best way to cut this is with good quality sizzors. Don’t try sizzors designed for fabric or paper. I have an electric sizzor that works great on cardboard but was difficult to use on this. I also have heavy duty sizzors and they were close to perfect.
The double sided tape is easy but does not result in a solid installation. I ended up using liquid nails. I did use pieces of double sided tape to place panels before final glue down to make sure of the fit of the panel.
The sheets come with a protective film. Leave this on until you have the panel in position. I used a sharpie to mark my cuts and make notes on the film. To eliminate confusion and accidents I drew arrows showing top and right . It would be very easy to mis-orient a sheet resulting in a loss of a sheet. The space between my counter tops and the cabinets is less than 18 inches and I had to cut every sheet.
If you cut your sheets so any error is on the too large side of things you will find that the sizzors allow you to make very straight cuts taking as little as a 16th of an inch of material at a time.
Buy the same colored pieces for edges and inside corners. They are nearly goof proof. These are hard and brittle and the joints won’t be perfect. I bought a package of the stick on foil used to cover switch and wall plate covers. Small pieces at the corners made the joints nearly invisible.
We did not use the foil for the wall plate covers instead opting for new plates that had color very similar to the bronze. They cost about $6 each and we needed 10 of them. We also replaced the white recepticals with brown ones including the two GFCI outlets. The plastic sheets have raised areas and you might need spacers to bring the receptials out about 1/4 inch. You can buy a package of spacers made just for this purpose.
I used 16 sheets of the plastic and six tubes of liquid nails. Total project cost was $550.00. It took me a full day, working carefully.
The result is eye popping and really enriched the atmosphere. We have a family room opposite the kitchen and will add these panels to an area above the gas fire place to add balance. Tile would have been nice but I am not sure it would have had the same pleasing effect.
Anonymous –
This product is very easy to install yourself and it looks great. It resembles very costly copper backsplash panels. I used sharp scissors to cut straight cuts, and used a sharp utility knife to do the outlet cutouts etc – just score lightly and you will be thru the panel in 3 to 4 swipes with the knife. I also used the double sided tape recommended with it to apply the panels to the walls – I was very skeptical on using the tape, but found it to be very easy to use and adheres well – cut the double sided tape and place it on the back of the panels to be installed then use the utility knife to help you remove the other side of the tape – pick at a corner and it was easy to remove the other side of the tape. Obviously pre fit each panel after it is cut then place double sided tape on panel after you are sure it will fit. Another thing I did was to use a marker – black or bronze – and ran it around the cabinet areas so when you cut the panels and your cut is not perfect you will not see it nearly as much cause it blends with the panels and does not stand out especially if you walls are alot lighter then the new panels. The outlet cover material matches very well with the backsplash panels. All in all it is a great product and easy to install, although it took me 2 days to complete I wanted to be certain I did not make any mistakes – as the panels are a little pricey – for being pretty much plastic -but great to work with and it looks great – would recommend.
Anonymous –
After purchasing new stainless steel kitchen appliances, and installing a new tile kitchen floor, we purchased this back-splash to hold us over until we can afford granite counter tops and a glass tile back-splash. Maybe we don’t need the glass tiles – since the result is amazing. The back-splash looks like real metal. You have to get up close to tell that it is not. The product is reasonably easy to work with, especially if you have experience putting up wallpaper, which I did. Each panel comes with a clear protective film. This film provides the perfect template to do measurements before cutting the actual panel. I just used heavy duty scissors and had no trouble cutting the panels. The only time I used a utility knife was to cut out a space for the outlets. I used the double adhesive backed tape that is sold along side of the panels to install the panels to the wall. The tape is easy to work with and sticks firmly. I did not find it necessary to use the heavy duty ‘glue in a tube’ as was recommended by others. The tape is easier to work with in my opinion, adheres strongly to the wall, and is definitely less messy. You can purchase a matching adhesive paper in the bronze finish to cover outlet covers. I also purchased bronze screws for the outlet covers – looks so great! Overall, I am so pleased with the result. My kitchen looks stylish, warm, and amazing!
Anonymous –
I purchased Fasade Thermoplastic Backsplash tiles which I gently hand sanded to ruff up so that paint would adhere to the surface. Next, I painted with cream satin paint, 2 coats. Next, I used my palm sander and distressed the raised areas of the details of the tile. Then I used a spray clear semi gloss protective sealer, 3 coats. I am ready to install. When installing behind the cooking range, I found that the panels measuring 18″ X 24″ would not work so I ordered a matching ceiling tile which was 24″ 48″. I did find that the tutorials were not very helpful regarding the simple details such as which is the top and which is the bottom of the panels but it is easy to figure out.
Anonymous –
We were able to install this in one night. We used the adhesive that was sold near the tile display in the store (looked like the recommended adhesive). It went up easily and looks AMAZING! It is worth the price. It completely changed the look of our kitchen and we get more compliments on it than anything else we’ve done.
(I’ve attached before and after pictures.)
Anonymous –
Used for my vintage camper as a panel on the door where the wood is rotting a tiny bit. It covers it well and matches the vintage theme. It is a bit expensive for one panel though.
Anonymous –
Beauty
Anonymous –
I used this to cover my kitchen bar area. The hardest part was to cut it and have it and have the pattern match. I was concerned about the durability since people kick their feet in that area so I bought extra to fix it later. It has been 2 years and still looks new. I took the edges and not only glued them but I also used finishing nails to tack them down. I also nailed down the corners of the tile that would be concealed. Then I used liquid nails on the rest. I took my time and it looks beautiful and is durable. I still get compliments and people assume the builder did it. I am a mother of of 3 small boys.
Anonymous –
I used this above my shower. It matches my kitchen backsplash and it is perfect. They are plastic so i dont have to worry about it rusting.
Anonymous –
This product, impossible to find at any other home improvement retailer, was ordered to match perfectly to existing product of similar color and construction already installed in our home. The original was installed nine years ago so it was doubtful that the identical item could be located now, but came to our rescue.
Anonymous –
Good product, fairly easy install. We had it up for 4 years when we got a new oven and found that the tile had melted and delaminated behind the stove.
Anonymous –
This product is beautiful. It looks like pressed tin but weighs next to nothing.
My problems:
1. I had a little trouble finding scissors sharp enough to cut accurately but finally settled on tin snips. I also had to cut around a window sill which was pretty tricky.
2. I used the J-trim for the outer edges which looks very nice. The corner piece worked great in the corner. However, the employee at recommended using the corner pieces along the bottom where the backsplash meets the countertop for a nice finish. I don’t disagree that it’s a nice finish but it made installation quite cumbersome and I had trouble getting it to stick to the back of the wall. *Oh, and be sure to clean, clean, clean your area prior to installation. Very important.
3. I did try using spray adhesive on the back of the panels at first thinking it would be less messy. But that doesn’t work. Use the adhesive in the tube that they recommend.
4. It’s a little tricky lining up the pattern and the panels aren’t cheap so be sure that you measure, measure, measure before cutting. Also, there is an overlap on the panels I used so be sure that you account for that overlap in your measurements.
5. I wanted my short pieces to be on the inside corner (where it’s less noticeable) so on my L-shaped kitchen I started on the left side for that wall’s installation and on the right side for the other installation. I think it avoided any questionable seams.
Overall, I really like the look of this product. It really dresses up my kitchen but I am a VERY inexperienced do it yourselfer so I had a pretty steep learning curve I guess. The employee at said “It’s super easy and goes up fast”. Well, to me, it didn’t go up fast. I had about 20 linear feet to install and it took me the entire weekend. I didn’t complete clean up until later in the week. And I didn’t think it was super easy but then I did have a tricky windowsill to go around so maybe it’s just me.
I am trying to sell this house so I wanted to dress up my kitchen. I’m not sure I will use this product in my new house but it certainly looks nice enough. Good luck.